25
Cookies help us deliver our services. By using our services, you agree to our use of cookies.
Accept Cookies Learn MoreLot
25
1 Used West Bond wire welder with controller.
Model: 7200a
SN: 10034
Volts: 115
Amps: 1
Cycles: 50/60
Techniquip Contoller
Model: FOI-150
SN: F31028
Mfg Date: 1997
General Info:
7200 Series provides separate functions on the same tool head to dispense epoxy, then to pick up chips, rotate them into alignment, and place them. All operation is controlled by West•Bond’s unique three-axis micromanipulator, working in combination with optical encoders under microprocessor control. The workpiece is held on a free anvil work holder, where chips are also arrayed for pick up.
The dual tool assembly is driven directly by the motor between the two positions for epoxy dispense and for vacuum pickup, with the transfer signaled by lift to a programmed elevation. Another programmed elevation is set to dispense epoxy without contact. This method is further enabled by the design of the “C Series” manipulator in which each axis is independently guided and therefore can be locked on command by the pneumatic brake. Control of vacuum for pick up and placement is by work sensing firing switch, with downforce adjustable from zero to approximately 75 grams. While the chip is held by vacuum, it can be rotated continuously by a motor by an operator’s optical encoder control.
Website: http://www.westbond.com/index.htm
Skidding and Load out charges: There will be loading and skidding charges added to your purchase at market rates for your convenience.
Location: Azusa, CA
Skidding: $75.00
Load Out: $40.00
Skidding and Load out charges:
There will be loading and skidding charges added to your purchase at market rates for your convenience.
MAAP Technologies Complete Facility
AUCTION DATE: lots start closing on Thursday, September 9th at 10:00 am PT
LOCATION: 1310 Mountain View Circle, Azusa, Calif.
INSPECTION: By appointment only. Please contact us to schedule. 818-495-3038
PICKUP: TBD
RIGGING:
There is no self-rigging. All Rigging and Load out will be completed by a contracted and approved Rigger.
18% Buyers Premium applies on all online purchases.
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms of Sale Agreement:
SELLER RESERVES THE RIGHT TO ACCEPT OR REJECT ANY AND ALL BIDS
Inspection date (day only) is:
By Appointment Only. Call 818 495 3038 to Schedule.
Inspection locations:
Various Locations, call for specific item.
Inspection by appointment only.
Call or Email Logan Hillseth logan@chrishillsethenterprises.com or Patrick Hillseth at (818)495-3038 patrick@chrishillsethenterprises.com
Your question has been sent to the auctioneer.
There was an error sending your enquiry, why not try again later
1 Used West Bond wire welder with controller.
Model: 7200a
SN: 10034
Volts: 115
Amps: 1
Cycles: 50/60
Techniquip Contoller
Model: FOI-150
SN: F31028
Mfg Date: 1997
General Info:
7200 Series provides separate functions on the same tool head to dispense epoxy, then to pick up chips, rotate them into alignment, and place them. All operation is controlled by West•Bond’s unique three-axis micromanipulator, working in combination with optical encoders under microprocessor control. The workpiece is held on a free anvil work holder, where chips are also arrayed for pick up.
The dual tool assembly is driven directly by the motor between the two positions for epoxy dispense and for vacuum pickup, with the transfer signaled by lift to a programmed elevation. Another programmed elevation is set to dispense epoxy without contact. This method is further enabled by the design of the “C Series” manipulator in which each axis is independently guided and therefore can be locked on command by the pneumatic brake. Control of vacuum for pick up and placement is by work sensing firing switch, with downforce adjustable from zero to approximately 75 grams. While the chip is held by vacuum, it can be rotated continuously by a motor by an operator’s optical encoder control.
Website: http://www.westbond.com/index.htm
Skidding and Load out charges: There will be loading and skidding charges added to your purchase at market rates for your convenience.
Location: Azusa, CA
Skidding: $75.00
Load Out: $40.00
General delivery information available from the auctioneer
Skidding and Load out charges:
There will be loading and skidding charges added to your purchase at market rates for your convenience.
MAAP Technologies Complete Facility
AUCTION DATE: lots start closing on Thursday, September 9th at 10:00 am PT
LOCATION: 1310 Mountain View Circle, Azusa, Calif.
INSPECTION: By appointment only. Please contact us to schedule. 818-495-3038
PICKUP: TBD
RIGGING:
There is no self-rigging. All Rigging and Load out will be completed by a contracted and approved Rigger.
18% Buyers Premium applies on all online purchases.
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms of Sale Agreement:
SELLER RESERVES THE RIGHT TO ACCEPT OR REJECT ANY AND ALL BIDS
Inspection date (day only) is:
By Appointment Only. Call 818 495 3038 to Schedule.
Inspection locations:
Various Locations, call for specific item.
Inspection by appointment only.
Call or Email Logan Hillseth logan@chrishillsethenterprises.com or Patrick Hillseth at (818)495-3038 patrick@chrishillsethenterprises.com