37
Cookies help us deliver our services. By using our services, you agree to our use of cookies.
Accept Cookies Learn MoreLot
37
1 Used FES International Spray Dryer with High-Pressure Pump and Blower Fan
Spray Dryer
Model: NC-10-8-3-1-160-B
S/N: D-15888-4099
Power: 460 V AC, 3 Phase, 60 Hz
Natural Gas: 3500cfm
Water: 50-60 Psi, 3 gpm/min
Compressed Air: 100psi, 30 scfm, clean and dry air
High-Pressure Pump
Model: HP-700-1.25-3-P-20-3K
S/N: D-16309-4099
Feed Pump
WAUKESHA Universal model 15 [ump with double "o" - ring seal and water coolantconnections for feeding product to the high pressure pump and circulating CIP solutions.
SUMITOMO .75kVa (1.0 hp) gear drive motor; Power: 460 VAC, 60Hz, 3 phase.
WEG Inverter speed control for varying flow rated to the pump.
In-line Filters
A Dual Filter-Strainer is installed immediately shead of the product feed tank to strain the fluid product to be dried. Two strainers are furnished, so that one may be cleaned while the other is operating.
This assembly is a model M-4 screen unit with 0.8 mm (.030") unless specified otherwise by the Purchaser. Each strainer has 0.19 m² (2.0 ft²) of perforated metal.
Unit is completely piped with four (4) manually-operated butterfly valves and fittings.
High Pressure Pump
Variable Speed Control
Inlet Air Filter
Blower Fan
Model: Inlet Fan
Type: BC-SW
S/N: 07-229172-1-1
Size: 300
ARR: 9R
Class: 3
Operation:
Product: Seaweed
Liquid Feed: KG/HR 2326 LBS/ HR
Feed Solids: 5%
Feed Temp: 37.4F
Inlet Temp: 32F
Exhause Temp: 140F
Evaporation Capacity: 2204 lbs/hr
Powder Rate(kg/hr): 122lbs hr
Powder Moisture: 5%
Water Make Up Tank:
FES 120L Tank
General Info:
Spray drying calculations take the ambient conditions such as humidity and temperature as well as ground-level into consideration. These parameters have a huge influence on the air amount required to dry the feed into powder. The main air system consists of air filters, pre-heating systems, air heater, supply fan and from time to time dehumidification system. The main air system is constructed according to the actual requirements of the product and the ambient conditions.
Skidding and Load out charges: There will be loading and skidding charges added to your purchase at market rates for your convenience.
Location: Springville, UT
Load Out: TBD
Skidding: TBD
Skidding and Load out charges:
There will be loading and skidding charges added to your purchase at market rates for your convenience.
***Assets are located at multiple locations.***
AUCTION DATE: lots start closing on Tuesday, December 14th at 10:00 am PT
LOCATION: **Note** Assets located at multiple locations. PLEASE READ THE DESCRIPTIONS!
1310 Mountain View Circle, Azusa, California
INSPECTION: By appointment only. Please contact us to schedule. 818-495-3038
PICKUP: TBD
RIGGING:
There is no self-rigging. All Rigging and Load out will be completed by a contracted and approved Rigger.
18% Buyers Premium applies on all online purchases.
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms of Sale Agreement:
SELLER RESERVES THE RIGHT TO ACCEPT OR REJECT ANY AND ALL BIDS
Inspection date (day only) is:
By Appointment Only. Call 818 495 3038 to Schedule.
Inspection locations:
Various Locations, call for specific item.
Inspection by appointment only.
Call or Email Logan Hillseth logan@chrishillsethenterprises.com or Patrick Hillseth at (818)495-3038 patrick@chrishillsethenterprises.com
Your question has been sent to the auctioneer.
There was an error sending your enquiry, why not try again later
1 Used FES International Spray Dryer with High-Pressure Pump and Blower Fan
Spray Dryer
Model: NC-10-8-3-1-160-B
S/N: D-15888-4099
Power: 460 V AC, 3 Phase, 60 Hz
Natural Gas: 3500cfm
Water: 50-60 Psi, 3 gpm/min
Compressed Air: 100psi, 30 scfm, clean and dry air
High-Pressure Pump
Model: HP-700-1.25-3-P-20-3K
S/N: D-16309-4099
Feed Pump
WAUKESHA Universal model 15 [ump with double "o" - ring seal and water coolantconnections for feeding product to the high pressure pump and circulating CIP solutions.
SUMITOMO .75kVa (1.0 hp) gear drive motor; Power: 460 VAC, 60Hz, 3 phase.
WEG Inverter speed control for varying flow rated to the pump.
In-line Filters
A Dual Filter-Strainer is installed immediately shead of the product feed tank to strain the fluid product to be dried. Two strainers are furnished, so that one may be cleaned while the other is operating.
This assembly is a model M-4 screen unit with 0.8 mm (.030") unless specified otherwise by the Purchaser. Each strainer has 0.19 m² (2.0 ft²) of perforated metal.
Unit is completely piped with four (4) manually-operated butterfly valves and fittings.
High Pressure Pump
Variable Speed Control
Inlet Air Filter
Blower Fan
Model: Inlet Fan
Type: BC-SW
S/N: 07-229172-1-1
Size: 300
ARR: 9R
Class: 3
Operation:
Product: Seaweed
Liquid Feed: KG/HR 2326 LBS/ HR
Feed Solids: 5%
Feed Temp: 37.4F
Inlet Temp: 32F
Exhause Temp: 140F
Evaporation Capacity: 2204 lbs/hr
Powder Rate(kg/hr): 122lbs hr
Powder Moisture: 5%
Water Make Up Tank:
FES 120L Tank
General Info:
Spray drying calculations take the ambient conditions such as humidity and temperature as well as ground-level into consideration. These parameters have a huge influence on the air amount required to dry the feed into powder. The main air system consists of air filters, pre-heating systems, air heater, supply fan and from time to time dehumidification system. The main air system is constructed according to the actual requirements of the product and the ambient conditions.
Skidding and Load out charges: There will be loading and skidding charges added to your purchase at market rates for your convenience.
Location: Springville, UT
Load Out: TBD
Skidding: TBD
General delivery information available from the auctioneer
Skidding and Load out charges:
There will be loading and skidding charges added to your purchase at market rates for your convenience.
***Assets are located at multiple locations.***
AUCTION DATE: lots start closing on Tuesday, December 14th at 10:00 am PT
LOCATION: **Note** Assets located at multiple locations. PLEASE READ THE DESCRIPTIONS!
1310 Mountain View Circle, Azusa, California
INSPECTION: By appointment only. Please contact us to schedule. 818-495-3038
PICKUP: TBD
RIGGING:
There is no self-rigging. All Rigging and Load out will be completed by a contracted and approved Rigger.
18% Buyers Premium applies on all online purchases.
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms of Sale Agreement:
SELLER RESERVES THE RIGHT TO ACCEPT OR REJECT ANY AND ALL BIDS
Inspection date (day only) is:
By Appointment Only. Call 818 495 3038 to Schedule.
Inspection locations:
Various Locations, call for specific item.
Inspection by appointment only.
Call or Email Logan Hillseth logan@chrishillsethenterprises.com or Patrick Hillseth at (818)495-3038 patrick@chrishillsethenterprises.com