8
GED MHM03500416R 84”W DUAL-ZONE OVEN / ROLL PRESS LINE, S/N 9536, MIN UNIT SIZE 12” X 12” RUNNING
1/17
Auctioneer has chosen not to publish the price of this lot
Windsor, Ontario
13.00%
18.00%
Description
GED MHM03500416R 84”W DUAL-ZONE OVEN / ROLL PRESS LINE, S/N 9536, MIN UNIT SIZE 12” X 12” RUNNING STRAIGHT & 9” X 9” RUNNING DIAGONALLY, MAX UNIT SIZE 84” X 120”, UNIT THICKNESS 3/8” – 2”, AUTO OPERATION, CS-DS-E 84”W X 4.5’L X 34” – 38”H MOTORIZED SKATE WHEEL INFEED CONVEYOR W/ 4”DIA. WHEELS ON 6” CENTERS, 4.5’L DUAL-ZONE HEATING OVEN, CAN RUN GREATER OR EQUAL TO 42”W IGU’S W/ SINGLE-ZONE WITH OPERATING TEMPERATURE 650-950 DEGREES F, LINE SPEEDS 3 – 35 FPM, EACH ZONE W/ PLC CONTROLLED AUTO IDLE STANDBY MODE, (3) EMITTER BANKS W/ TOTAL OF (16) EMITTERS, WATLOW LED TOUCHPAD TEMPERATURE CONTROLLER, 2’L ROLL PRESS W/ (3) TOP & (3) BOTTOM 6”DIA/ X 88” RUBBER ROLLS, VARIABLE SPEED, MOTORIZED ROLL HEIGHT ADJUSTMENT, LED DISPLAY, 2HP MOTOR, CS-DS-E 84”W X 6.5’L X 34” – 38”H MOTORIZED SKATE WHEEL OUTFEED CONVEYOR, 4”DIA. WHEELS ON 6” CENTERS, 84”W X 4’L BALL TRANSFER OUTFEED CONVEYOR W/ 1.5”DIA. BALLS ON 6” CENTERS, APPROX. 275”L X 125”W X 67”H AND 11,000LBS (SUBJECT TO BULK BID LOT 1) (NOTE: MACHINE HAS BEEN PROFESSIONALLY DISCONNECTED) (RIGGING FEE $500)
Auction Details
Rigging/Removals
T&Cs & Important Info
Ask seller a question
GED MHM03500416R 84”W DUAL-ZONE OVEN / ROLL PRESS LINE, S/N 9536, MIN UNIT SIZE 12” X 12” RUNNING STRAIGHT & 9” X 9” RUNNING DIAGONALLY, MAX UNIT SIZE 84” X 120”, UNIT THICKNESS 3/8” – 2”, AUTO OPERATION, CS-DS-E 84”W X 4.5’L X 34” – 38”H MOTORIZED SKATE WHEEL INFEED CONVEYOR W/ 4”DIA. WHEELS ON 6” CENTERS, 4.5’L DUAL-ZONE HEATING OVEN, CAN RUN GREATER OR EQUAL TO 42”W IGU’S W/ SINGLE-ZONE WITH OPERATING TEMPERATURE 650-950 DEGREES F, LINE SPEEDS 3 – 35 FPM, EACH ZONE W/ PLC CONTROLLED AUTO IDLE STANDBY MODE, (3) EMITTER BANKS W/ TOTAL OF (16) EMITTERS, WATLOW LED TOUCHPAD TEMPERATURE CONTROLLER, 2’L ROLL PRESS W/ (3) TOP & (3) BOTTOM 6”DIA/ X 88” RUBBER ROLLS, VARIABLE SPEED, MOTORIZED ROLL HEIGHT ADJUSTMENT, LED DISPLAY, 2HP MOTOR, CS-DS-E 84”W X 6.5’L X 34” – 38”H MOTORIZED SKATE WHEEL OUTFEED CONVEYOR, 4”DIA. WHEELS ON 6” CENTERS, 84”W X 4’L BALL TRANSFER OUTFEED CONVEYOR W/ 1.5”DIA. BALLS ON 6” CENTERS, APPROX. 275”L X 125”W X 67”H AND 11,000LBS (SUBJECT TO BULK BID LOT 1) (NOTE: MACHINE HAS BEEN PROFESSIONALLY DISCONNECTED) (RIGGING FEE $500)
Meloche Windows - Surplus to the Ongoing Operations
Ends from
Venue Address
6144 Morton Industrial Dr.
Windsor
Ontario
N9J 3W3
Canada
EXCLUSIVE RIGGING APPLIES TO THIS AUCTION, SEE INFORMATION BELOW:
Attn: Les Lovell
Mobile: 1-647-966-5739
llovell@caesarswindsor.com
Rigging to Include: Electrical disconnect, dismantle and prep where applicable and loading onto provided flatbed trucks. All prices are plus fees and taxes. Contact rigger for pricing on loading into containers, dry vans, palletizing lots, crating, wrapping, blocking, etc.
Important Information
Auction Date & Time: lots start closing on Tues. 06/25/2024 11:00 am
Location: 6144 Morton Industrial Drive, Windsor, ON, N9J 3W3
Inspection: Monday June 24th, 9AM - 4PM or By Appointment
18% Buyers Premium applies on all online purchases.
Featuring:
1998 (Upgraded in 2010) BILLCO GED Intercept Complete Horizontal Insulated Glass Manufacturing Line, Can Produce up to 1,200 High-Quality, Warm-Edge IGU’s per 8hr Shift w/ “Intercept Ultra” Stainless Steel Continuous U-Shaped Spacer Frames, Overall Footprint Approx. 60.5’L x 30.5’W x 13.5’H, Consisting of The Following Machines:
- 1998 (Upgraded in 2010) GED MIS24001200411E Generation 2 “Intercept Ultra” IGU Insulated Glass Spacer Frame Building Machine, s/n 234, Ultra Conversion Upgrade in 2010 to run 0.0077” Thickness Stainless Steel, Production Rate; (3,000) 24” x 36” Frames (No Muntin) per 8hr Shift, Min Frame Length 6” x 6”, Max Frame Length 21.5’ (Based on 20’L Transfer Conveyors – Equivalent of 36” x 84” Patio Door or 50” x 70” Picture Unit), Spacer Width 7/32” – 7/8”, Frame Height 0.300” (+/- 0.005”), Screw Size #8-32, Line Speeds 1-8 Frames/Min (24” x 36” Frame – No Muntin), Auto or Semi-Auto Operation, Auto Width Adjustment, Auto Muntin Location Notching, Auto Gas Hole Punching of Spacers for Single or Dual-Hole, Auto Remake Capability, Control Sole w/ PC-Based Control, Monitor, Allen Bradley 1394 Digital Servo Motion Controller, Variable Speed Amplifier Drives, WinFrame II Software, 36” Dia. Dual-Reel Portable Motorized Uncoiler w/ (2) Rotating Spools each 0.5HP, Laser Measuring/Linear Bearing Loop Control Unit w/ 125249 Ultrasonic Sensor, Ultra Conversion Feeder Press/Punch Station, s/n 1342, Ultra Conversion Roll Former, s/n 1342 w/ (8) Top Horizontal, (9) Bottom Horizontal & (1) Vertical Pairs of Rolls & LED Display, Corner Crimper w/ LED Display, 1-3/8”W x 20’L Belt Transfer Conveyor w/ 0.5HP Motor, Overall Dimensions Approx. 524”L x 116”W x 86”H and 6,250lbs
- 2010 GED MSMEXT410000E Smart Linear Co-Extruder, s/n 13544, LinearSkip or LinearU Extrusion, Min Frame Length 6” x 6”, Max Frame Length Unlimited, Spacer Width 7/32” – 7/8”, Line Speed 80 – 94 FPM, Sealant & Matrix Thickness Application Accuracy +/- 0.002”, Sealant Start/Stop Accuracy +/- 0.050”, Auto or Semi-Auto Operation, Expandable Desiccant Matrix Application w/ Automatic Servo Position Controlled Conveyor Width Adjustment & Application Heads, Quick-Release Hold-Down Wheels, Precision Positive Displacement Gear Pumps, Encoder-Based Dispensing for Starts/Stops/Skips, 1-1/16”W x 6’L Infeed & Outfeed Belt Conveyors, PC Based Control w/ PRO-FACE 15” LCD Touchscreen Display, WinEXTRUDE Software, Temperature Settings, Calibration Wizard for Customized Setups & Remote Diagnostics, Approx. 152”L x 48”W x 76”H and 2,900lbs
- (2) GED MHMP41042DE 42:1 Ratio 55-Gal Drum-Type Hot Melt Sealant / Desiccant Pumps, 22”Dia. X 35”H Drum Size, Heavy Duty Dual Elevators, Insulated Material Hoses
- 2000 BILLCO WORKHORSE II 684-8 84”W 8-Burhs Flip-Top Flat Glass Washing & Drying Machine, s/n W099180, Max Glass Width 84”, Min Glass Length 14.5” Diagonal, Glass Thickness 1/16” – ¼”, 13 – 36 FPM, 49-1/2”L Loading Section w/ Motorized Donut Roll Conveyor, 40”L Detergent Washing Section w/ (2) Pair of 8”Dia. X 85”W Low-E Bristle Brushes w/ 3HP TEFC Brush Motor & 80-Gal Cap. Water Holding Tank, (2) 20kW Heaters, OMEGA CN76000 LED Touchpad Temperature Controller, 0.5HP Pump, 40”L Rinse / Final Rinse Section w/ (2) Pair of 8”Dia. x 85”W Low-E Bristle Brushes w/ 3HP TEFC Brush Motor, 40-Gal Cap. Water Holding Tank, 1HP Pump, 38”L Drying Section w/ 20HP TEFC Blower & Sound Baffling System w/ (2) Air Knives, 49.5”L Unloading Section w/ Motorized Donut Roll Conveyor, Detergent Washing & Rinse / Final Rinse Sections w/ Flip-Top Manual Hydraulic Lift, Spray System w/ (2) Copper Spray Lines per Brush, (2) Stainless Steel Spray Lines per Brush (Final Rinse), Line Strainers & Auto Water Saver (Final Rinse), 84”W x 35.5”H Motorized Donut Roll Conveyor w/ 3”Dia. Rolls on 7” Centers & 1HP TEFC Motor, Approx. 240”L x 140”W x 100”H and 10,000lbs
- 2010 BILLCO TITAN 500 AT-500S Gallons / Day RO Reverse Osmosis Water Treatment System, s/n 88642, 150 PSI, 110/220V, 50/60 CY, 1 Ph, (2) 2.5” x 21” Membrane Elements, 5-Micron Sediment & 10-Micron Carbon Block Chlorine 4.5” x 10” Pre-Filters, 1/3HP 150 PSI Pump, Low Pressure Switch, 120-Gal Cap. Vertical Polyethylene Water Storage Tank Approx. 30”Dia. x 47”H w/ 24”Steel Stand
- (3) BILLCO Caster-Type Transfer Tables, (1) 2.5’ x 7’ x 3’H Track-Mounted, s/n W0-85114-4, Dimensions 84” x 32” x 36”H, (1) 2.5’ x 4’ x 3’H, s/n N/A, Dimensions 48” x 30” x 36”H, (1) 4’ x 4’ x 3’H Pneumatic, s/n W0-85114-1 w/ 8”Dia. Suction Cup, Dimensions 50” x 50” x 36”, All Transfer Tables w/ ¾”W x 2”Dia. Swivel Casters on 6” Centers
- GED M813-0310 42”W x 20’L Overhead Spacer Frame Hanging Conveyor, Transports Completed Frames from Extruder to Transfer Tables Between Washer & Oven / Roll Press Line, (3) Feed Chains on 15” Centers w/ Hooks on 5” Centers, 7.5 FPM Conveyor Speed, On/Off Photo Sensors Automatically Advance Conveyor When Frames Are Removed, Approx. 262”L x 96”W x 36”H
- GED MHM03500416R 84”W Dual-Zone Oven / Roll Press Line, s/n 9536, Min Unit Size 12” x 12” Running Straight & 9” x 9” Running Diagonally, Max Unit Size 84” x 120”, Unit Thickness 3/8” – 2”, Auto Operation, CS-DS-E 84”W x 4.5’L x 34” – 38”H Motorized Skate Wheel Infeed Conveyor w/ 4”Dia. Wheels on 6” Centers, 4.5’L Dual-Zone Heating Oven, Can Run Greater or Equal to 42”W IGU’s w/ Single-Zone with Operating Temperature 650-950 Degrees F, Line Speeds 3 – 35 FPM, Each Zone w/ PLC Controlled Auto Idle Standby Mode, (3) Emitter Banks w/ Total of (16) Emitters, WATLOW LED Touchpad Temperature Controller, 2’L Roll Press w/ (3) Top & (3) Bottom 6”Dia/ x 88” Rubber Rolls, Variable Speed, Motorized Roll Height Adjustment, LED Display, 2HP Motor, CS-DS-E 84”W x 6.5’L x 34” – 38”H Motorized Skate Wheel Outfeed Conveyor, 4”Dia. Wheels on 6” Centers, 84”W x 4’L Ball Transfer Outfeed Conveyor w/ 1.5”Dia. Balls on 6” Centers, Approx. 275”L x 125”W x 67”H and 11,000lbs
- REX MANUFACTURING 118KVA & 93KVA Transformers, 600V to 480Y/277V
2011 BILLCO CNC 2200 108” x 144” Glass Optimization Cutting Machine w/ Edge Deletion, Z-95” Z-Axis Cutting Head and Automatic Cutting Wheel Changing, s/n 38672-01A , Max Glass Size 108” x 144”, Min Glass Size 48” x 60”, Glass Thickness 0.09” – 0.75”, Air Flotation Table Size 110” x 168” x 36”H, Dense Woven Black Felt Surface, (3) Left & (3) Right 5/8”W Recessed Feed Chains on 15” Centers, Bridge Travel 162”, Max Cutting Speed 4,500 IPM, Cut Tolerance +/- 0.015”, Deletion Speed 4,000 IPM, Auto Edge Detection & Edge Deletion, Front Locating Stops, Z-95 SUPER HEAD 360 Degree Servo-Controlled Rotary Cutting Head w/ Servo-Controller Z-Axis for Automatic Glass Thickness and Wheel Dia. Adjustment, Pneumatic Cutting Pressure Adjustment, Pressurized Lubrication System, Advanced Cutting Wheel Guidance, Auto Cutting Wheel Changing w/ (6) Spare Cutting Wheel Stations, Maintenance Free AC Digital Motors, High Res / High Torque Digital Step & Direction Servo Motors, Rack & Pinion Bridge and Head Travels, Aluminum Alloy Bridge, CNC Control Console w/ (2) 17” Displayers, BILLCO BUTLER Operating Interface Software, HP3 BATCHBAN Optimization Software (Full Version), Supports Motion Control (G-Code) & Machine Control (Ladder Logic Programs) and Remote Diagnostics, Operating & Maintenance Manual, Mechanical & Electrical Drawings, Spare Parts List, Transformer, Dimensions of Glass Cutting Machine 202”L x 170”W x 63”H, Dimensions of Control Console 48”L x 36”W x 63”H, Dimensions of Electrical Cabinet 45”L x 20”W x 84”H
ROLLTECH INDUSTRIES MCT 912-A-2BB 9’ x 12’ x 36”H Single-Axis Air Floatation Breakout Table, Overall Table Size 109” x 145” x 36”H, Max Glass Size 108” x 144”, 38.5”, 32”, 38.5” Breakout Sections, (2) Table Length Pneumatic Breaker Bars, Controls on Table End, DAYTON 4C329 4HP, 3,450 RPM TEFC Direct Drive Blower w/ Start/Stop Button Control Stations on (3) Sides, (4) Screw-Type Adjustable Feet
KEAR FABRICATION K-05A 72”W x 10”D x 60”H Double-Sided A-Frame Flat Glass Dolly, (2) Swivel & (2) Fixed 8”Dia. x 2.5”W Phenolic Casters, Screw-Type Floor Lock, (2) Safety Bars, Rubber Contact Surfaces
UNIVAL 520 L Dual-Head Vinyl Welding Machine, 81” Head Travel, Fixed Left & Movable Right Heads, (4) OMRON Temperature Controllers, (2) E5ES LED w/ Touchpad & (2) E5C2 Analog w/ Dial, Transformer
(2) GIOVANNI / APB COPY S Single-Head Copy Routers, 9,5” x 21.75” x 33.5”H Table Size, 1HP Motor, (2) Horizontal Pneumatic Clamps, 48”L x 3”H Fence, s/n’s 0663/89001, 0275/6319
SAMPSON MN 14 14” Double Miter Saw, 5.75” x 31.5” x 35”H Table Size, Cutting Cap. 7”H x 1”W at Max Height & 3.75”W x 3”H at Max Width, Cutting Accuracy +/- 0.005”, +/- Min Arc, Arbor Dia. 5/8”, Blade Speed 12,000 SFM, Cycle Time 3 Sec, Pneumatic Blade Actuation w/ Foot Pedal, (2) 1.5HP, 3,450 RPM Motors, (2) 36”L x 3.75”H Fence, s/n 89049
SAMPSON MN 12 12” Double Miter Saw, 5.75” x 31.5” x 35”H Table Size, Cutting Cap. 5.5”H x 1”W at Max Height & 3.75”W x 2.5”H at Max Width, Cutting Accuracy +/- 0.005”, +/- Min Arc, Arbor Dia. 5/8”, Blade Speed 11,000 SFM, Cycle Time 3 Sec, Pneumatic Blade Actuation w/ Foot Pedal, (2) 1.5HP, 3,425 RPM Motors, (2) 32.75” x 2.25” Fence, s/n 89048
LETARTE ECON-O-MITRE EM 11 B 11” Double Miter Saw, Cutting Cap. 3” x 3”, Table Height 35”, Pneumatic Blade Actuation, Foot Pedal Control, s/n 473284 (Note: Missing 1 Motor)
ELU MGS 72 300mm (11.81”) Bench-Top Miter Saw w/ Cabinet Base, 11” x 25” x 37”H Table Size, 3,400 RPM Motor, 100”L Cap. X 2.25”W x 1.5”H Manual Stop, 18”L x 3”W x 1.5”H Outfeed Fence, s/n 181019
ELU MGS 72 300mm (11.81”) Bench-Top Miter Saw, 11” x 25” x 4.75”H Table Size, 1,450W – 3,800 RPM Motor, 27” x 24” x 27.5”H Steel Stand, 5/8” Thick Plywood Top, s/n 3856
LINCOLN RF66KB361 14” Vertical Contour Metal Cutting Band Saw, 16” x 19.75” x 38”H Table Tile 15 Degree Left & Right, Max Height Under Guard 8”, Wheel Dia. 14”, Blade Size 5/8”W x 113”L, Variable Blade Speeds 30 – 90 MPM, Blade Shear, Blade Welder / Grinder, Work Light, s/n B361329
GARRETT TOOLING Pneumatic Door Frame Machine, 42” x 84” Cap., Working Height 38”, (6) 3”Dia. Pneumatic Clamps, 92) For Left Jamb, (2) For Right Jamb, (2) For Header, Manual Rack & Pinion Width Adjustment
DELTA 10 10” Radial Arm Saw, Blade Size 20” x 30” x 4.75”H, Rip Cap. 0-14” In / 12” – 24” Out, Blade Bevel Angle 90 Degree Left & Right, Radial Arm Swing Range 45 Degree Left & Right, 3,450 RPM, 30” x 42” x 33”H Steel Frame Stand, ¾” Thick Plywood Top
CRAFTSMAN 113.278570C 10” Radial Arm Saw, 28” x 44” x 37”H Table Size, Rip Ca. 1.5” – 17.5” In / 10.5” – 27.5” Out, 3,450 RPM, LCD Miter / Bevel / Elevation / Rip Display, 2-Door Cabinet, s/n 88356M0067
DELTA HOMECRAFT 18” Bench-Top Drill Press, 8” x 8” Table Size, 8” LR x 6.25” FB Base Size, Quill Travel 3-1/2, s/n BM9838
ITW RANSBURG Electrostatic Waterbase Paint Finishing System, AquaTank 5-Gal Cap. 21”Dia. x 32”H Voltage Isolation Tank, 55-PSI, 75786 Spray Gun w/ Max Paint Pressure 100 PSI & Hose, 76580-61001 40W Control Unit / Power Supply, Output Voltage 0 – 10V, Output Current 1/2A, 9040 CASCADE Low Voltage Module, s/n 241111
Lot of (6) 10L Cap. Pressure Pots, 80-PSI, (2) Spray Guns, (2) Regulators & Hoses
ZEKS HEATSINK 35HSEA100 35 CFM Cycling Refrigerated Compressed Air Dryer, R-22, 1/3HP Compressor Motor, 1/15HP Fan Motor, s/n 244975
WOOD’S Powr-Grip Manual Ladder Lift System
=================================================================
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
- Monday – Friday, 8:00 AM EST – 8:00 PM EST
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms and Conditions
PAYMENT: All payments must be in either Cash, Certified Cheque, Wire Transfers or Company Checks must be accompanied with a bank letter guaranteeing irrevocable payment to Infinity Asset Solutions Inc., Visa & Mastercard will be accepted for total payments of $2,000.00 or less (amounts more than $2,000.00 will be subject to a 3% administrative fee).
Payment is due by: 2PM Wednesday June 26th, 2024.
Your credit card added through the Bidspotter.com fully secure and PCI compliant registration process will be charged a $2000.00 deposit in order to be approved to bid within the auction. You will not be approved without your credit card entered at the stage of registration being charged a deposit of $2000.00
Credit Card Payments: Payments via credit card are accepted up to $2000.00 final invoice total (amounts more than $2,000.00 will be subject to a 3% administrative fee). Any invoice total larger than $2000.00 must be paid by wire transfer or certified check. Your deposit may be applied to your final invoice amount, even if your final invoice is larger than $2000.00. Credit Card Payments can only be processed in CANADIAN FUNDS.
Removal deadline: 2PM Friday July 12th, 2024.
EXCLUSIVE RIGGING APPLIES TO THIS AUCTION, SEE INFORMATION BELOW:
Attn: Les Lovell
Mobile: 1-647-966-5739
llovell@caesarswindsor.com
Rigging to Include: Electrical disconnect, dismantle and prep where applicable and loading onto provided flatbed trucks. All prices are plus fees and taxes. Contact rigger for pricing on loading into containers, dry vans, palletizing lots, crating, wrapping, blocking, etc.
Accounting: Victoria 905-669-8893 Ext. 207, vwhitman@infinityassets.com
Banking Information (Wire Transfers):
CANADIAN WIRE TRANSFER INSTRUCTIONS
Beneficiary Bank: ROYAL BANK OF CANADA
3300 HIGHWAY #7
CONCORD, ONTARIO
Beneficiary Customer:
INFINITY ASSET SOLUTIONS INC.
ACCOUNT #: 1007137
TRANSIT #: 00192
BANK #: 003
SWIFT # ROYCCAT2
FOR CUSTOMERS FROM USA:
INTERMEDIARY BANK: J.P. MORGAN, NEW YORK
ABA#: 021000021
IBAN #: 003401028600192
Terms and Conditions of Sale Persons participating in the auction shall be bound by ALL of the following terms and conditions, which are subject to amendments and modifications by the Auctioneer at the time of auction. 1. This catalogue is meant merely as a guide. The Auctioneer believes the descriptions contained herein to be correct, but make no warranty in connection therewith. 2. Auctioneer reserves the right to sell subject to reserve and to bid for its own account and for the accounts of others, whether by verbal or written proxy, all lots are subject to prior sale. 3. The Auctioneer reserves the right to refuse any applicant the privilege of bidding or attending at the auction and may revoke such privilege at any time. 4. All Articles will be sold to the highest bidder conforming to the bid process, provided that the Auctioneer reserves the right to sell articles by individual, group lots and “in bulk,” as he deems appropriate. The Auctioneer reserves the right to sell on behalf of third parties, its own account or on the account of others. Should any dispute arise between two or more bidders or as to any bid, the lot in question may, at the Auctioneers discretion, be immediately put up again and resold. The Auctioneer shall regulate all matters relating to the conduct of the auction and his decision shall be final and binding on all bidders. The record kept by the clerk of sale, shall in all cases be accepted by the bidder as final. 5. All sales shall be concluded as indicated by the Auctioneer and no Purchaser may thereafter revoke his bid. Title to the lots purchased shall not pass until payment in full of the purchase price is received. 6. ALL SALES ARE FINAL, ON AN “AS IS WHERE IS,” “IN PLACE” “WITH ALL FAULTS” BASIS WITH NO CONDITIONS OR WARRANTIES WHETHER EXPRESSED OR IMPLIED, STATUTORYOR OTHERWISE, INCLUDING WITHOUT LIMITATION, WARRANTIES OR CONDITIONS, AS TO TITLE, DESCRIPTION, FITNESS FOR PURPOSE, QUANTITY, QUALITY, MERCHANTABILITY, STATE, CONDITION, LOCATION OR OTHERWISE. NO SALE SHALL BE INVALIDATED AND THE AUCTIONEER SHALL HAVE NO LIABILITY FOR A MISDESCRIPTION OF ANY ARTICLE OR LOT WHETHER CONTAINED IN A CATALOGUE, ADVERTISEMENT, OR OTHERWISE. DESCRIPTIONS HAVE BEEN PREPARED FOR GUIDE PURPOSES ONLY AND SHALL NOT BE RULED UPON BY THE PURCHASER FOR ACCURACY OR COMPLETENESS. PLEASE INSPECT ALL ITEMS BEFORE BIDDING. PURCHASERS SHALL BE DEEMED TO HAVE RELIED ENTIRELY UPON THEIR OWN INSPECTIONS AND INVESTIGATIONS. 7. A deposit of equal to 25 percent of the purchases shall be made at the time of sale. The balance of the purchase price must be paid in full before or immediately after the conclusion of the auction. All payments must be in Cash, Certified Funds, Visa, MasterCard or Interac, Wire Transfers or Company Checks must be accompanied with a bank letter guaranteeing irrevocable payment to Infinity Asset Solutions Inc. Deposits on account of purchases may be made in advance of the auction and the balance thereof will be refunded immediately after the auction. The Auctioneer reserves the right to put articles back up for auction if deposit is not received at or before the time of sale. 8. No article shall be removed unless paid for in full and articles purchased shall be removed within the guidelines and terms stipulated. The Purchaser shall be responsible for all the costs of removal and shall be liable for all damages, including without limitation, any environmental damage, caused during or as a result of the removal. Purchasers shall comply with all environmental laws and regulations including requirements as to bonding of movers. No claims shall be allowed after removal of the purchased article. 9. Where available, documents of transfer, including motor vehicle ownership documents, which are in possession of the Auctioneer, will be provided to the Purchaser following the auction or as soon thereafter as such documents are available. 10. No purchaser may assign, transfer or dispose of his rights in any article purchased before he has paid the purchase price in full. 11. Purchasers shall pay applicable federal and provincial taxes, or furnish exemption certificates at the time of payment for goods purchased. All purchases are subject to Federal Harmonized Sales Tax (H.S.T.) at all times (including buyer's premium). No exceptions whatsoever. 12. Time shall be of the essence. If a Purchaser fails to make payment of remove goods within the time periods hereinabove provided, the Auctioneer may resell the article purchased by auction, private contract or otherwise, as the Auctioneer in his discretion deems advisable, and the Purchaser shall be liable for the shortfall and all costs expenses, including but not limited to interest rates (a minimum of 1.5% per month or 18% per annum), legal fees, moving and storage (a minimum rate of $2.00/sq.ft. per month) and commissions, incurred such as resale. 13. The Auctioneer assumes no responsibility or any liability once title passes, which occurs at time of payment in full. Purchasers are advised to prearrange for insurance coverage of their purchase. Title will revert to the seller in the event purchaser does not remove his purchases by the time specified. 14. If the Auctioneer is unable to deliver an article sold to a Purchaser due to fire, theft or any other reason whatsoever, the Auctioneer shall reimburse the Purchaser for all monies paid to the Auctioneer in respect of the article and the Auctioneer shall have no further liability to the Purchaser arising from or relating to such loss, including without limitation, any damages or loss of profits. 15. Bidders acknowledge that any auction site is a potentially dangerous place with noxious, corrosive and pressurized substances being present, heavy equipment being operated and electric circuits being live. Every person at the Auction Site before, during and after the auction sale shall be deemed to be there at their own risk with notice of the condition of the premises, the activities on the premises and the conduct of third parties, and the Bidder shall so advise his/her agents and employees. No person shall have any claim against the auctioneer, his agents, employees or principals for any injuries sustained for damages to or loss of property which may occur from any cause whatsoever.
EQUIPMENT REMOVAL PROCEDURES TERMS & CONDITIONS
The following are the standard procedures and terms and conditions for the removal of equipment or other items purchased at an Infinity Asset Solutions Inc. (“Infinity”) sale:
- All invoices must be paid in full prior to removal of equipment/ Each invoice must be marked “Paid in Full” and initialed by an authorized Infinity representative.
- All buyers are solely responsible for coordinating the removal of items purchased at the Auction and all associated costs.
- Buyers are responsible for, at their expense: a. Proper and safe disconnection and termination of all electrical, gas, water and/or air lines to machines conforming to all governing building codes; b. Shearing flush to the floor of all anchor bolts or fasteners; c. Erecting safety barriers around pits and holes in the floor created by removal of equipment until repaired; d. Repair all holes in the floor, walls or roof created by the removal of items purchased conforming to all governing building codes; e. Removing, off premises, machine oils and all hazardous materials (including all contaminants) contained in items purchased; f. Repairing all damage cased to the premises by a buyer, its representative or any other party hired by a buyer for the removal of items purchased; g. Leaving the work area in a clean, broom-swept condition conforming to all governing building codes; h. Any other specific terms and conditions communicated by Infinity before, during or after the auction sale; i. Removal of items purchased by the time and date set by Infinity before, during or after the auction sale; and j. The safety of all of a buyer’s employees, agents or representatives including all movers/riggers hired by such buyer.
- Prior to removal, all buyers, or any movers or riggers hired by a buyer, must provide to Infinity a satisfactory certificate of insurance evidencing at leas $5,000,000 in comprehensive liability insurance coverage (including workers compensation and automobile) per person, per occurrence.
- Prior to removal, an authorized Infinity representative must examine and approve the removal of all items purchased at the sale. Such approval shall be indicated by this representative initialing all invoices.
- No items shall be removed until after the auction sale. Removal hours are weekdays only between 8:00 a.m. and 4:00 p.m. unless otherwise specified.
- Buyers and their movers/riggers are jointly and severally liable for all damages, costs and expenses to the premises or any other assets which were cased by any of them, their employees, agents or representatives whether through negligence or otherwise. The Buyer indemnifies and saves Infinity harmless from any and all costs, expenses and claims suffered or incurred by Infinity as a result of any act or omission of such buyer and/or any mover or rigger retained by a buyer.
NO ITEMS SHALL LEAVE THE PREMISES UNTIL THE ABOVE HAS BEEN COMPLIED WITH TO INFINITY’S SATISFACTION.
NOTE: Buyers, please provide all movers or riggers hired by you with a copy of these procedures/terms and conditions as you will be held liable for their conduct.
