2016 - Mitsubishi Mdl. FGC25N Fork Lift, LPG, 5000Lb Capacity, 3-Stage Mast, 187" Reach, 24" Load Center, Side Shift, Solid Tire
The featured lots page shows the best lots from the BidSpotter.com website. These featured lots have been chosen by our auctioneers and showcase their premier items.
This is just a small selection of the huge volume of lots on BidSpotter.com. You can search across the entire site for the items you are looking for. If you can't find what you are looking for you can set up alerts to notify you when that item is added to the site.
2016 - Mitsubishi Mdl. FGC25N Fork Lift, LPG, 5000Lb Capacity, 3-Stage Mast, 187" Reach, 24" Load Center, Side Shift, Solid Tire
Landis Tool 24X96 Cylindrical Grinder, 24" Swing, 96" Between Centers, 4"W Grinding Wheel
Monarch Lathe, 37-1/2" Swing, 156" Between Centers, Carriage, Tool Post, 19" Diameter Steady Rest, Tail Stock, 24-1/2" Diameter 4-Jaw Chuck
Meuser & Co 5" Horizontal Boring Mill, 57" x 57" Rotary T-Slot Table, Spindle Speeds up to 710 RPM
Silo Storage Tower, 60' Tall, 7660 Cu Ft
Milltronics/ International MachineTools Model VMC20 Vertical Machining Center s/n 9756, New in 2007, IMT-GE Fanuc I Series CNC Control, 40Taper Sp...
Daewoo Model MYNX500 Vertical Machining Center s/n AV5EHF21A3, New in 2000, Fanuc Series 21-M CNC Control, 40Taper Spindle, 24ATC, 1200mmX500mm (4...
Milltronics Model VM24 Vertical Machining Center s/n 5434, New in 1998, Centurion 6 CNC Control, 40Taper Spindle, 20ATC, 24"X45" Table, Chip Auger...
Milltronics Model VM24 Vertical Machining Center s/n 6875, New in 2001, Centurion 6 CNC Control, 40Taper Spindle, 20ATC, 24"X45" Table, Chip Auger...
Hyster Model E65XN-40 Electric Forklift s/n A268N18564P, 4,900lb cap., Hard tires, 3-Stage Mast, Sideshift, 4' Forks, 11,716hours, w/charger
2019 Sullair Shop-Tek ST7 Rotary Screw Air Compressor, Integrated Air Dryer, Model ST0709AC, S/N 37219050641, 3 Phase, 3,520 RPM, 8.6 Bar @ 125 PS...
Gardner-Denver 15-HP Apex 10 Total System Rotary Screw Air Compressor, DRO, Model NEX15, S/N D1227660, Integrated Air Dryer,
Big Ass Fan 18' Powerfoil 3.0 Industrial Ceiling Fans, Variable Speed, 10-Blade System, 2 HP
2015 Crown SC Series 3,700 LB. 3-Wheel Electric Forklift, S/N 10020023, Model SC5245-40, 36V, 190" Lift Height, 83" 2-Stage Mast, Gen Braking, Sid...
2016 Kalmar Ottawa Spotter Truck/ Terminal Tractor, Model T2 4X2, VIN 11VJ813A4GA00124, Hydraulic Lifting Fifth Wheel, 11,827 Hours
Kalmar Ottawa Spotter Truck/ Terminal Tractor, Model 4x2, S/N 34759, Hydraulic Lifting Fifth Wheel
2018 APS 850s Autobagger System, SN AP00085233, Unwinder Feeder, DRO, 19,045 Lifetime Count
2018 APS 550 Autobagger System, Unwinder Feeder, S/N AP00085327, 115,070 Lifetime Count
2014 APS AB225 One Step Autobagger System, S/N AP00043555, Unwinder Feeder, Flow Controls, Adjustable Heat Range, 3,636,028 Lifetime Count, PI-412...
Loveshaw Little-David CF-25 Box Erector, Model CF25T/60, S/N 471237025T/60, S/N CF25OI0116XX1, Single Phase, 110V, 60 HZ, 1/3 HP
Yale 4,000 Lb. Electric Forklift, with Battery, 42" Forks, Triple Stage Mast
Schechtl Model UKV 150 S Box Brake, s/n UK 14502, 55" Of Bottom Fingers, 38" Of Top Fingers
Caterpilllar Model MC60DSA Electric Fork Lift, 6,000 Lb. Capacity, 48" Forks,s/n 8BBO-1685, with Battery
Ras Model 73.30 CNC Folding Machine, s/n S-73.00B/6000-2, 11 Gauge X 10' Capacity, New 2005, System 6000 Control
Filler and seamer is capable of 15 cans per minute or 2.7 Bbl/Hr. depending on the operator and product being filled. The EVOLUTION series is buil...
Right to Left Flow Wrapper. Was rebuilt by BD Briggs, LLC in 2019. Unit is a "B" Frame with Allen Bradley 4 Axis Servo system. Infeed conveyor len...
Peels, Tops / Tails, Haves, Up to 6 Melons / Min., 49"L X 31"W X 91.5"T, 230 Volt, 3 phase, 75 PSI / .5" IPS.
Each unit automatically singulates, aligns, and orients corn, feeding it into an A&K Power Corn Cutter. The system is equipped with a metering con...
66 Gallon Capacity, Scrap surface agitation, with replaceable plastic blades, Kettle valve and 2 temp problem ports at bottom of kettle, PLC Contr...
Single Motion Agitation with side and bottom nylon scrapers (scraper blades are removable). 26" Dia. x 24" Deep. Approximately 50 gallon usable ca...
Groen NHFP natural gas fired braising pan is 41 3/8" wide left to right and is 9" deep. It is capable of a firing rate of 144,000 BTU/hr.
Model # WSP-2123, Stainless steel construction.
The oven has a cooking area of 27 square feet, operational temp range is 300-600 degrees F. For cooking pizzas, bread, pasta bakes, and desserts q...
Dual Chamber, MFG: 11/2006, Voltage 220, 60 Hz, 3ph, 34 amps.
With Paper Separator Inserter
Double arm Sigma Mixer with stainless steel contact points. Mixer is manual crank dump, HMI operator display with push button Stop, Start, Jog, an...
Min. Tank Capacity 40 lbs., Gross Input 110000 BTU/h, Burner Pressure 4 in W.C., Gas Type: Nat, 115 volt, 1 amp, 60 Hz.
Single station semi automatic tray sealer. 480 Volt, 3 Phase, 60Hz, 8.25 AMPS electrical required. Several size dies included for different trays....
The REISER VEMAG water wheel attachment is designed by REISER to be used in conjunction with a VEMAG pump. The model SCD Shredder Cutter Depositor...
Siemens Hydraulic Power Pack Stainless Steel
2014 SPE Tech AG Gigh Pressure Pump Skid 14-7002
Apple Wedger is capable of coring and wedge cutting in one single function. The wedger has multiple options for cutting configurations from a 4-16...
Model # BFIS-2D-S7, Electrical Requirements: 2 compressors 208 Volt 3 Phase 60 Hz., Overall Dimensions 80" Wide X 42" Deep X 89", 26.5" Wide X 30"...
Hermle C800V 3-Axis Mill from 1998 The machine has powered time of 80,257 hours and program time of 16,828 hours as shown in the picture of the co...
2020 HWACHEON Hi-Tech 550 B MC CNC Turning Center w/ Live Milling, s/n M125367F5LA, Fanuc 0i-TD CNC Control, 31.5" Swing Over Bed, 23.23" Max Cutt...
2012 Nicholson Model 40" r2 R.H. 50 HP Sliding Ring Debarker, 40" ID Max Dimensions, (3) Carbide Cutting Arms, (1) 27' chain infeed, (1) 16' x 10....
1995 Mellott Model Rosser-Head 36" 30 HP Head Debarker, Type 10, 20' Turn Table, w/ 32' Vibratory Outfeed, S/N 9420038
McDonough 125 HP Double Cut Resaw Bandmill, 62" x 9.25" Wheel, 10" Wide Blade, w/ Scrap Outfeed, S/N 62MA302, Internal Asset ID: 000540
Mereen-Johnson Model 312-DC/0PH1 5-Blade Straight Line Rip Saw w/ Built-In Dust Collection 460 v, 72 AMPS, 60 Hz, 23" Intake
1992 Honeyville Dust Collection System, (2) Bag Houses, (1) Cyclone, (2) Dumping Stations, screw conveyors, Infeed lowers, and Conveyors
2022 SII Dry Kilns 45,000 BF Prefabricated Aluminum & Stainless Kiln with SS Wall Panels, Direct Fired Gas Burners, & Kiln Dry 9060 Computerized C...
Lot: (4) 2012 Nyle 25' x 40' Steam Wood Drying Kilns w/ Boiler Control System, Internal Asset ID: 003544 (Please Note: Kilns Share Center Walls an...
2006 Kalmar Industries Ottawa Model 30 Yard Truck, Mileage: 139,951, Hours: 30,249, S/N 313322
Caterpillar Model IT18F Wheel Loader, PID: 62F00311, Hours: 22,844, Enclosed w/ AC, Repaired Engine Hole, Slipping Transmission, Flat Tires, Batte...